SATA(7D) Devices SATA(7D)


NAME


sata - Solaris SATA framework

DESCRIPTION


Serial ATA is an interconnect technology designed to replace parallel ATA
technology. It is used to connect hard drives, optical drives, removable
magnetic media devices and other peripherals to the host system. For
complete information on Serial ATA technology, visit the Serial ATA web
site at http://www.serialata.org.


Up to 32 SATA devices may be plugged directly to each SATA HBA and up to
15 SATA devices may be plugged directly to each SATA port multiplier
supported by the Solaris SATA framework. The actual number of pluggable
devices may be lower, and is limited by the number of device ports on the
SATA HBA or the SATA port multiplier. The maximum data rate is either
1.5Gb/sec. or 3.0Gb/sec., depending on the capability of a SATA device,
port multiplier and SATA HBA controller.


The Solaris SATA framework adheres to the Serial ATA 1.0a specification
and supports SATA-2 signaling speed 3.0Gb/sec. SATA devices that are
connected to SATA HBAs controlled by a SATA framework-compliant HBA
driver are treated by the system as SCSI devices. The Solaris SCSI disk
driver (sd(7D)) is attached as a target driver for each device node
created by the SATA framework. You can use the cfgadm(1M) utility to
manage hot plugged and unplugged SATA devices.

FILES


/kernel/misc/sata
32-bit ELF kernel module (x86).


/kernel/misc/amd64/sata
64-bit ELF kernel module (x86).


ATTRIBUTES


See attributes(5) for descriptions of the following attribute:


+---------------+-----------------+
|ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+---------------+-----------------+
|Architecture | x86 |
+---------------+-----------------+

SEE ALSO


cfgadm(1M), prtconf(1M), cfgadm_sata(1M), attributes(5), ahci(7D),
nv_sata(7D), sd(7D), si3124(7D)


Serial ATA 1.0a Specification -- Serial ATA International Organization.


Serial ATA II (Extension to Serial ATA 1.0.a.) -- Serial ATA
International Organization.

DIAGNOSTICS


The messages described below may appear on the system console as well as
being logged. All messages are presented in one of the following formats
and are followed by the diagnostic message:

sata: WARNING: <controller/devices/.. path>:


or:

sata: NOTICE: <controller/devices/.. path>:


...where <controller/devices/.. path> identifies a specific SATA HBA
issuing a diagnostic message shown below.

SATA port X: link lost.

Communication (via serial link) between the HBA and the device
plugged to the specified SATA device port has been lost.


SATA port X: link established.

Communication (via serial link) between the HBA and the device
plugged to the specified SATA device port has been established.


SATA port X: device reset.

The device plugged to the specified SATA device port has been reset.
The reset may be due to a communication or command error, command
timeout, or an explicit request from the host.


SATA port X failed.

The specified SATA device port failed and is in an unusable state.
You can change the port state by deactivating the port and activating
it again using cfgadm SATA hardware-specific commands (see
cfgadm_sata(1M)).


SATA port X error.

An error was detected in specified SATA device port operations.


SATA device detached at port X.

Communication (via serial link) between the HBA and the device
plugged to the specified SATA device port has been lost and could not
be re-established. The SATA framework assumes that the device is
unplugged from the specified SATA device port.


SATA device detected at port X.

Communication( via serial link) between the HBA and the device
plugged to the specified empty SATA device port has been established.
The SATA framework assumes that the new device is plugged to the
specified SATA device port.


SATA disk device at port X.

This message is followed by a disk description specifying the disk
vendor, serial number, firmware revision number and the disk
capabilities.


SATA CD/DVD (ATAPI) device at port X.

This message is followed by a SATA CD/DVD description specifying the
DVD vendor, serial number, firmware revision number and the DVD
capabilities.


SATA device at port X cannot be configured. Application(s) accessing
previously attached device have to release it before newly inserted
device can be made accessible.

The port cannot be configured because there is application using the
previous attached device, so the application must release it, then
the newly inserted device can be configured.


Application(s) accessing previously attached SATA device have to release
it before newly inserted device can be made accessible.

The target node remained and it belongs to a previously attached
device. This happens when the file was open or the node was waiting
for resources at the time the associated device was removed. Instruct
event daemon to retry the cleanup later.


sata: error recovery request for non-attached device at cport X.

When error recovery is requested, the device is not yet attached.


SATA device at port X is not power-managed.

When property pm-capable on the target device node setting fails, the
SATA device won't be power-managed.


SATA disk device at port X does not support LBA.

The disk device plugged into specified SATA device port does not
support LBA addressing and cannot be used.


Cannot identify SATA device at port X - device is attached.

IDENTIFY (PACKET) DEVICE data cannot be retrieved successfully after
the device is attached to the SATA port.


sata: <HBA driver name><instance number>:hba attached failed.

The SATA HBA instance attach operation failed. This HBA instance
cannot be configured and is not available.


sata: invalid ATAPI cdb length<command cdb length>.

The length of the command cdb is greater than that the device can
support.


sata: invalid sata_hba_tran version X for driver <HBA driver name>.

The specified SATA HBA driver and the SATA framework are
incompatible. The driver cannot attach and SATA HBAs controlled by
this driver (and devices plugged to this SATA HBA ports) are not
available.


sata_hba_attach: cannot create SATA attachment point for port X.

The specified SATA device port cannot be configured in the system and
a device plugged to this port could not be not be configured and
used.


sata_create_target_node: cannot create target node for device at port X.

The device target node for the device plugged to the specified SATA
device port could not be created. As a result, the device cannot be
configured and used.


May 13, 2017 SATA(7D)